EPS@ISEP | The European Project Semester (EPS) at ISEP

Differences

This shows you the differences between two versions of the page.

--- log [2014/06/13 15:51] – [7th Meeting (2014-04-30)] team2
+++ log [2014/06/18 16:22] (current) – [13th Meeting (2014-06-12)] team2
@@ Line 37: / Line 37: @@
   - focusing on researching materials
+====6th Week Report ====
+  - 3 different materal list was prepeared
+  - started to write sustainabilty report
+  - chosen one option of the material list
+====7th Week Report ====
+  - presentation of interim report was done
+  - started to prepare to interim report
+  - first version of leaflet was created
+  - all deliverables were uploaded to the wiki
+====8th Week Report ====
+  - Concerned about heat that inside of the cork case
+  - worked on power consumption calculation
+====9th Week Report ====
+  -  created Fritzing diagram
+  - calculated estimation autonomy
+  - started to project management
+  - finalized sustainability part of final report
+====10th Week Report ====
+  - created the power diagram
+  - created the signal diagram
+  - searched sopfware solution
+  - finalized ethics and deontology part of the report
+  - designed second version of leaflet
+====11h Week Report ====
+  - arranged priorities for the development of the sofware
+  - finalized project management part
+====12th Week Report ====
+  - started to write paper
+  - recieved the components
+  - got some feedback for marketing report and corrected
+====13th Week Report ====
+  - created the poster
+  - recieved the cork block and started to design case
+  - finalized paper
+  - created final presentation
+  - created lat version of the leaflet
+  - started experiments
 ====== Meetings ======
@@ Line 123: / Line 171: @@
 **Minute:**
-The material list was chosen in three option. According to the question we informed about components.
+The expectation for the interim presentation was asked to supervisors and according to them, we prepeared to interim presentation. Also, receiving time for components was asked.
 ==== 8th Meeting (2014-05-08) ====
                        Calculation of ΔT
@@ Line 134: / Line 181: @@
 Arduino :
-  * Input voltage (recommended)           7-12V
+  * Input voltage (recommended)           7-12 V
-  * Input voltage (limit)                 6-20V
+  * Input voltage (limit)                 6-20 V
-  * Operating Voltage                      5V
+  * Operating Voltage                      5 V
-  * DC Current   per I/O Pin              40 MA
+  * DC Current   per I/O Pin              40 mA
-  * DC Current for 3.3V Pin               50 MA
+  * DC Current for 3.3V Pin               50 mA
 -This pin outputs a regulated 5V from the regulator on the board.
@@ Line 189: / Line 236: @@
+**Minute:**
+ΔT that is inside of the cork was tried to calculate but was agreed to use temprature stick to measured the ΔT because of the diffculties that is to calculate. power consumption was tried to calculated and the doubts were argued.
 ==== 9th Meeting (2014-05-15) ====
   - what do you expect from our project? we need spesific answers because of the project management.
@@ Line 195: / Line 245: @@
   - Estimation of the autonomy
 https://drive.google.com/file/d/0BxN1665smBF_WTZmREVVUXNxUGc/edit?usp=sharing
-==== 10th Meeting (2014-05-15) ====
+**Minute:**
+expectation of the project manaegment was asked to supervisors. fritzing diagram  of the prototype was shown and estimation of the autonomy was calculated and shown.
+==== 10th Meeting (2014-05-22) ====
   - Estimation of the autonomy(corrected) https://drive.google.com/file/d/0BxN1665smBF_dDFkc0lNTmM2WTg/edit?usp=sharing
   - Power diagram
@@ Line 205: / Line 258: @@
 {{:signaldiagram.jpeg?300|}}
+**Minute:**
+Estimation of the autonomy was corrected by supervisors. Afterthat, power and signal diagram has shown. the proposal of the software solution was shown to supervisors and some feedback was gotten.
 ==== 11th Meeting (2014-05-28) ====
@@ Line 219: / Line 275: @@
   -  Start saving data in the SD card
   - Developed and android app
+  -
+**Minute:**
+We had some priorities before meeting. At the meeting, we asked that which priorities are more important than the others. The most important one is to make it work by USB maybe after to make it work by bluetooth and accroding to the answers we were start to work on them.
 ==== 12th Meeting (2014-06-05) ====
@@ Line 224: / Line 285: @@
   - what is the deadline of the paper?
   - which part of report do we suppose to consider for paper?
+**Minute:**
+Structure of the paper was asked to supervisors and they have explained us. ıt should be consider state of the art, project devlopment but also we should mention about (not much) marketing and sustainability.
+==== 13th Meeting (2014-06-12) ====
+  - show the visual interface in computer
+**Minute:**
+Last version of prototype and  the visual interface were shown in the last meeting and gotten some feedback. the supervisors recomended us to think about aerodynamic of device on the board. Also, they informed us that we have a meeting on 23th june with IT Sector( the company that provided us the materials).
 ===== Activities =====
 //Please register here all project activities//

Trace: • log

Differences

Search

Navigation

Print/export

Tools

QR Code